noflate

Use this skill when integrating noflate into Rust code. Focus on the crate's actual API shape and usage patterns, not generic compression background.

What this crate exposes

• noflate::deflate for raw DEFLATE (RFC 1951)
• noflate::gzip for GZIP (RFC 1952), plus Crc32 / crc32
• noflate::zlib for ZLIB (RFC 1950), plus Adler32 / adler32
• Shared root types: Error, Result, Format

Each format module exposes the same main shape:

• One-shot helpers: compress(data) -> Result<Vec<u8>>, decompress(data) -> Result<Vec<u8>>
• Streaming types: Encoder, Decoder

Choosing the right API

1. Pick deflate, gzip, or zlib based on the wire format you need.
2. Use compress / decompress for one-shot data.
3. Use Encoder / Decoder when data arrives incrementally or output must be consumed in chunks.
4. Use EncodeOptions when you need fixed Huffman blocks, stored blocks, or buffering control.

Usage gotchas

• This crate is #![no_std]; it requires alloc, not std.
• The streaming API is sans-io: feed(data) pushes input, output() borrows produced bytes, advance(n) marks bytes as consumed.
• One-shot compression uses buffered input internally; for similar behavior in streaming code, use EncodeOptions::new().buffer_all_input().
• sync_flush() is for continuing a DEFLATE stream across message boundaries. It is useful for permessage-deflate; do not treat it like finish().
• reset_history() is only for no_context_takeover style flows. Do not reset state between messages unless the protocol requires it.
• Format::detect(&data) needs enough prefix bytes to distinguish framing; it returns None for too-short input.
• Checksum helpers are format-specific: gzip uses CRC-32, zlib uses Adler-32.

API patterns to preserve

One-shot:

let compressed = noflate::deflate::compress(b"hello")?;
let decompressed = noflate::deflate::decompress(&compressed)?;

Streaming encoder:

let mut enc = noflate::deflate::Encoder::new();
enc.feed(b"chunk1")?;
enc.feed(b"chunk2")?;
enc.finish()?;
let out = enc.output().to_vec();
enc.advance(out.len());

Streaming decoder:

let mut dec = noflate::deflate::Decoder::new();
dec.feed(&compressed)?;
let out = dec.output().to_vec();
dec.advance(out.len());
assert!(dec.is_finished());

Options:

use noflate::deflate::EncodeOptions;

let dynamic = EncodeOptions::new();
let fixed = EncodeOptions::new().fixed_huffman();
let stored = EncodeOptions::new().stored();
let buffered = EncodeOptions::new().buffer_all_input();
let limited = EncodeOptions::new().max_block_input_bytes(32 * 1024);

WebSocket permessage-deflate:

let mut enc = noflate::deflate::Encoder::new();
enc.feed(message)?;
enc.sync_flush()?;
let frame = enc.output().to_vec();
enc.advance(frame.len());
// Per RFC 7692, strip the trailing 0x00 0x00 0xFF 0xFF before sending.

enc.reset_history(); // only when no_context_takeover is negotiated

Format detection:

match noflate::Format::detect(&data) {
    Some(noflate::Format::Gzip) => {}
    Some(noflate::Format::Zlib) => {}
    Some(noflate::Format::Deflate) => {}
    None => {}
}

Practical hints

• If you already have all input bytes, start with compress / decompress before reaching for the streaming API.
• If you use the streaming API, always drain output() and call advance() after consuming bytes.
• For WebSocket permessage-deflate, strip the final 0x00 0x00 0xFF 0xFF after sync_flush().
• EncodeOptions belongs to noflate::deflate, but the same options are used by gzip::Encoder and zlib::Encoder.
• The crate performs no I/O itself, but the sans-io API plugs into std::io::Write / Read with a small adapter: Write::write forwards to feed and drains output into the inner sink; Read::read pulls from output and tops up via feed from the inner source. See examples/io_bridge.rs for a runnable DeflateWriter / DeflateReader pair.